 |
This package comes with BiXPower BP100 battery, a high capacity (96 Wh), small size ( 180 x 110 x 22.5mm or 7.2" x 4.2" x 0.9"), light weight (621g or 1.4 lb) lithium ion rechargeable battery, a DC Special Cable that is specially designed for a ResMed S9 CPAP machine. It can power ResMed S9 PAP machines.
Battery Running Time: Depending on CPAP Machine setting (such as CPAP pressure, breathing rate, optimal mask seal and whether humidifier, heated tubing and exhalation pressure relief disabled) and running environment, a CPAP machine may need as much as 90W power or as little as 10W power. So the battery running time may vary a lot. To maximum battery running time, please turn off CPAP Machine humidifier and heater, set the pressure as low as possible. The estimated running time will be around one night or so on an average CPAP pressure, average breathing rate, optimal mask seal and with the humidifier, heated tubing and exhalation pressure relief disabled.
The package comes with one BP100 battery + One S9 DC cable + AC Charger + Car charger
To use this battery with ResMed S9 CPAP machine, just plug in the ResMed S9 cable to battery Port I, set Port I output voltage at 24V, like this:
Its compact size allows it to easily fit into a laptop/notebook carry bag.
Battery Specifications:
| Model: | BP100 | Capacity: | 96 Watt-Hour | | Battery Cell: | Lithium-ion | | Input Charging Port: | Input Voltage Range: DC 12 ~ 24V. Connector Size: 5.5 x 2.5mm | | Outputs: | Port I:
Output Voltage: 16V, 19V or 24V selectable
Output Connector Size: 5.5 x 2.5mm
Maximum Output Current: 4A @16V, 3.5A@19V, 2.5A@24V
Port II: Nominal Output Voltage 11.1V
Output Voltage Range 9V ~ 12.6V
Output Connector Size: 3.5 x 1.35mm;
>Maximum Output Current: 5A
Port III: 5V USB Port; Maximum Output Current: 2.A
Total maximum output with all 3 outputs: 65W
| | Charging time /Temperature | 4-6 hours / 0～45 ℃
| | Size | 180 x 110 x 22.5mm ( or 7.2" x 4.2" x 0.9") | | Weight: | 621g ( or 1.4 lb) | | Power Indicator: | 4 level LED indicator | | Built-in Protection Circuit: | -Over-charge ; Over-discharge; Over current ;Over temperature
- Short circuit protection | | Operating Temperature: | -20～ 60 ℃ | | Storage Temperature: | - 20～40 ℃
|
This battery is made with high quality Panasonic Li-ion battery cells. It also has a 5V USB port can power many small devices such as smart phones, tablets.
This Universal External Lithium Rechargeable Battery Pack can provide power for laptop computers, digital cameras, digital photo frames, PDAs, cell phones, DVD players.
This battery features 3 output ports.
Output Port I
 utput Port I features 3 different regulated voltages through a hardware volt selection switch: 16V, 19V, 24V. This port can be used to power laptop notebook computers. Please set the port I output voltage close to your laptop power adapter output voltage or laptop's input voltage.
Please set Port I at 24V for ResMed S9 machine
Output Port II & Port III
Port II's output voltage range is 9V to 12.6V. Nominal voltage is 11.1V. When the battery is fully charged, its voltage is 12.6V. Output voltage will then decrease gradually. Most of the time, the output voltage will be around 10V ~ 11V ( nominal voltage is 11.1V). When the voltage drops to 9V, the port will shut off and stop providing power. This port can be used to power portable DVD players and digital photo frames.
Output III is a 5V USB port. Its maximum output current is 2.1A, which can be used to power or charge iPad, tablet computers and any other device that can be charged from a USB port (USB power cable not included).
Charge the battery: This battery can be charged from any 100V ~ 240V, 50Hz/60Hz AC power source with the battery AC charger.
It also can be charged from a 12V car cigarette socket with enclosed car charger
This battery has built-in charging controller to control the charging process. It can accept a very wide range of voltage for charging. You can use a regular power adapter with 12V to 24V DC power to charge the battery. The battery charge port is a 5.5 x 2.5mm female jack, therefore a 5.5 x 2.5mm male connector is required.
|
|
|